Average Cost of Concrete

Buyers typically pay for concrete by the cubic yard or by the square foot installed. Main cost drivers include material mix, slab thickness, reinforcing, finishing work, and local labor rates. This guide provides cost ranges in USD for common scenarios and highlights where prices vary.

Item	Low	Average	High	Notes
Materials (cement, aggregate, water, admixtures)	$110	$135	$180	Per cubic yard; varies by mix and region
Delivery/Dump fees	$75	$100	$150	Distance and fuel surcharges apply
Labor & installation	$3/sq ft	$5/sq ft	$6.50/sq ft	Includes finishing; thicker slabs cost more
Formwork & reinforcement	$1.50	$2.50	$4.00	Rebar, wire mesh, or fiber
Permits & inspections	$50	$150	$600	Depends on jurisdiction
Delivery/Disposal of spoil	$50	$100	$250	Container rental may apply
Taxes & overhead	$0	$0.50/sq ft	$1/sq ft	Varies by locality

Assumptions: region, slab size, thickness, reinforcement, and crew hours.

Overview Of Costs

Typical cost range for a standard 4-inch-thick, 1,000-square-foot slab installed is about $6,000 to $8,000. For a thicker or reinforced slab, or a driveway with finishing options, costs can rise to $9,000–$15,000. Per-cubic-yard pricing for materials generally falls in the $110–$180 range, with total installed costs reflecting labor, forms, and permits. The per-square-foot installed range commonly spans $5 to $8, depending on thickness, finish, and edging.

Cost Breakdown

Materials	Labor	Equipment	Permits	Delivery/Disposal	Warranty
$110–$180/yd³	$3–$6/ft²	$0.50–$1.50/ft²	$50–$600	$75–$150	Typically 1–2 years

Labor formula: labor_hours × hourly_rate. Assumes typical crew of 2–4 workers and standard finish.

What Drives Price

Key cost drivers include slab thickness, concrete mix design (standard vs. high-strength, low-alkali), reinforcement type and spacing, and finished surface texture. Substrate conditions, weather, and access for trucks also influence delivery and labor time. Concrete with specialty admixtures or decorative finishing adds cost. SEER-based regional pricing differences are less relevant than local labor rates and material sourcing.

Ways To Save

Smart budgeting tips include planning for off-peak scheduling, consolidating multiple pours, selecting standard finishes, and requesting bundled quotes that cover materials, labor, and permits. Choosing a simpler edge finish or a standard 4-inch thickness can reduce costs. Verify that the estimate clearly delineates concrete, reinforcement, forms, and finishing work to avoid surprise charges.

Regional Price Differences

Three-region comparison shows modest to notable variations due to material transportation and labor markets. In the Northeast, prices tend to be 5–12% higher on average than nationwide baselines because of stricter code compliance and higher crew wages. The Midwest often presents mid-range pricing, with typical totals +/- 0–8% from national averages. In the Southwest, heat-driven curing and shorter haul routes can keep costs near the national average or slightly below it, with regional adjustments of -3% to +6% depending on demand.

Labor & Installation Time

Impact of crew size and time matters: a standard 1,000 sq ft pour may require 6–8 man-hours per 1,000 sq ft for basic finishing, plus additional hours for edging and curing. Heavier pours, such as 6-inch slabs or reinforced sections, can double labor hours. If a crew is delayed by weather or site prep, total project time increases and cost may rise due to labor drift.

Additional & Hidden Costs

Common add-ons include non-standard finishes (stamped, stained), slope adjustments for drainage, long-haul delivery surcharges, weather insurance, and temporary power needs. Debris removal, form rental, and edge forms can stack up. Some projects require a concrete pump, which adds equipment rental and fuel costs. Always confirm disposal fees and clean-up charges in the estimate.

Real-World Pricing Examples